sc
--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Ver0.6.2 - Built on Jun 27 2016 17:41:43
--------------------------------------------------------------------------------
EMA VALUE : 001
123
Lock value  = 174
GATE CYC    = 0x00008421
GATE CODE   = 0x40404040
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-g0f31196-dirty (Dec 12 2017 - 11:30:39)

PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK =  800000000, HCLK = 200000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c73984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]
VER  = 1
BOARD= [s5p4418-X]
LCD  = S70
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
RGB: display.0
DISP: W= 800, H= 480, Bpp=32
DONE: Logo bmp 1024 by 600 (3bpp), len=1843254 DRAW: 0x47000000 -> 0x46000000 Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4664584 Bytes = 4.4 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (chitranjan@chitranjan-ThinkPad-T440) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #9 SMP PREEMPT Sat Nov 11 16:42:35 IST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HD101 selected
[    0.000000] Display: S70 selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x63600000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] rquest persistent memory from 635fc000 (00000000)-00004000
[    0.000000] Initialized persistent memory from 635fc000-635fffff
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK =  800000000, HCLK = 200000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @c1418000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259839
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 androidboot.console=ttyAMA0 androidboot.serialno=0123456789abcdef initrd=0x49000000,0x100000 lcd=HD101 fbcon=rotate:1 lcd=S70,128dpi
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 827364k/827364k available, 221212k reserved, 272384K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xef800000 - 0xfee00000   ( 246 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef600000   ( 758 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc088338c   (8685 kB)
[    0.000000]       .init : 0xc0884000 - 0xc08bc000   ( 224 kB)
[    0.000000]       .data : 0xc08bc000 - 0xc0934d68   ( 484 kB)
[    0.000000]        .bss : 0xc0934d8c - 0xc0b0ebe8   (1896 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736)
[    0.048000] pid_max: default: 32768 minimum: 301
[    0.048000] Security Framework initialized
[    0.048000] SELinux:  Initializing.
[    0.048000] Mount-cache hash table entries: 512
[    0.048000] Initializing cgroup subsys debug
[    0.048000] Initializing cgroup subsys cpuacct
[    0.048000] Initializing cgroup subsys memory
[    0.048000] Initializing cgroup subsys freezer
[    0.048000] CPU: Testing write buffer coherency: ok
[    0.048000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.048000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.048000] Setting up static identity map for 0x40629100 - 0x40629158
[    0.048000] L310 cache controller enabled
[    0.048000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.092000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.132000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.172000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.176000] Brought up 4 CPUs
[    0.176000] SMP: Total of 4 processors activated (6377.47 BogoMIPS).
[    0.180000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.184000] pwm: max = 50000000 hz
[    0.184000] prepare_gpio_suspend:
[    0.184000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.184000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.184000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.184000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.184000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.184000] dummy: 
[    0.184000] NET: Registered protocol family 16
[    0.184000] persistent_ram: uncorrectable error in header
[    0.184000] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[    0.188000] console [ram-1] enabled
[    0.192000] [Register machine platform devices]
[    0.192000] mach: add amba device uart-pl011.0 
[    0.192000] mach: add amba device uart-pl011.1 
[    0.192000] mach: add amba device uart-pl011.2 
[    0.192000] mach: add amba device uart-pl011.3 
[    0.192000] mach: add amba device uart-pl011.4 
[    0.192000] mach: add amba device uart-pl011.5 
[    0.192000] mach: add amba device pl08xdmac.0 
[    0.192000] mach: add amba device pl08xdmac.1 
[    0.192000] mach: add amba device ssp-pl022.0 
[    0.196000] mach: add device syncgen [2]
[    0.196000] mach: add device lcd 
[    0.196000] mach: add device i2c bus (array:3) 
[    0.196000] mach: add device Real Time Clock  
[    0.196000] mach: add device generic pwm (array:4)
[    0.196000] mach: add device generic gpio (array:6)
[    0.200000] mach: add device i2s (array:1) 
[    0.200000] mach: add device spdif tx
[    0.200000] mach: add device usb_ehci
[    0.200000] mach: add device usb_ohci
[    0.200000] mach: add device usb otg
[    0.200000] mach: add device ion-nxp
[    0.200000] mach: add device adc
[    0.200000] mach: add graphic device opengl|es
[    0.200000] [Register board platform devices]
[    0.200000] plat: board revision 7
[    0.200000] plat: add dynamic frequency (pll.1)
[    0.200000] plat: add device adc temp
[    0.200000] plat: add framebuffer
[    0.200000] plat: boot from mmc.0
[    0.200000] plat: add device sdmmc [0]
[    0.200000] plat: add device sdmmc [1]
[    0.204000] plat: add backlight pwm device
[    0.204000] plat: add device keypad
[    0.204000] plat: add device spdif playback
[    0.204000] plat: add device asoc-es8316
[    0.204000] plat: add device nxp-v4l2
[    0.208000] plat: register spidev
[    0.208000] plat: add touch(ft5x0x) device
[    0.208000] plat: add touch(goodix) device
[    0.208000] plat: goodix: irq=144 (80)
[    0.208000] plat: add touch(himax) device
[    0.208000] plat: add touch(it7260) device
[    0.208000] plat: add onewire ts device
[    0.208000] plat: add iio adc device
[    0.208000] plat: add device hdmi-cec
[    0.208000] plat: add device nxp-gmac
[    0.208000] plat: add device gpio_led
[    0.208000] 
[    0.208000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.208000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.208000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.208000] hw-breakpoint: CPU 3 debug is powered down!
[    0.208000] hw-breakpoint: CPU 1 debug is powered down!
[    0.208000] hw-breakpoint: CPU 2 debug is powered down!
[    0.208000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.208000] hw-breakpoint: CPU 0 debug is powered down!
[    0.208000] Serial: AMBA PL011 UART driver
[    0.208000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.212000] console [ttyAMA0] enabled
[    0.216000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.220000] uart-pl011.2: ttyAMA2 at MMIO 0xc00a2000 (irq = 8) is a PL011 rev3
[    0.224000] uart-pl011.3: ttyAMA3 at MMIO 0xc00a3000 (irq = 9) is a PL011 rev3
[    0.228000] uart-pl011.4: ttyAMA4 at MMIO 0xc006d000 (irq = 10) is a PL011 rev3
[    0.232000] uart-pl011.5: ttyAMA5 at MMIO 0xc006f000 (irq = 11) is a PL011 rev3
[    0.256000] bio: create slab <bio-0> at 0
[    0.264000] gpiochip_add: registered GPIOs 0 to 31 on device: GPIOA
[    0.268000] gpiochip_add: registered GPIOs 32 to 63 on device: GPIOB
[    0.272000] gpiochip_add: registered GPIOs 64 to 95 on device: GPIOC
[    0.276000] gpiochip_add: registered GPIOs 96 to 127 on device: GPIOD
[    0.280000] gpiochip_add: registered GPIOs 128 to 159 on device: GPIOE
[    0.284000] gpiochip_add: registered GPIOs 160 to 167 on device: GPIOALV
[    0.288000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.292000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.296000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.304000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.308000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.312000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.316000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.324000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.328000] nxp_ion_probe success!!!
[    0.332000] SCSI subsystem initialized
[    0.336000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.340000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.344000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.348000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.352000] usbcore: registered new interface driver usbfs
[    0.356000] usbcore: registered new interface driver hub
[    0.360000] usbcore: registered new device driver usb
[    0.364000] i2c-gpio i2c-gpio.3: using pins 159 (SDA) and 158 (SCL)
[    0.372000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.376000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.380000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.384000] Linux media interface: v0.10
[    0.388000] Linux video capture interface: v2.00
[    0.392000] pps_core: LinuxPPS API ver. 1 registered
[    0.396000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.400000] PTP clock support registered
[    0.412000] axp_mfd 3-0034: AXP (CHIP ID: 0x06) detected
[    0.420000] axp22_ldo1: 3000 mV 
[    0.428000] axp22_aldo1: 700 <--> 3300 mV at 3300 mV 
[    0.436000] axp22_aldo2: 700 <--> 3300 mV at 1800 mV 
[    0.444000] axp22_aldo3: 700 <--> 3300 mV at 1000 mV 
[    0.452000] axp22_dldo1: 700 <--> 3300 mV at 3300 mV 
[    0.460000] axp22_dldo2: No configuration
[    0.464000] axp22_dldo2: 700 <--> 3300 mV at 700 mV 
[    0.468000] axp22_dldo3: No configuration
[    0.472000] axp22_dldo3: 700 <--> 3300 mV at 700 mV 
[    0.476000] axp22_dldo4: No configuration
[    0.484000] axp22_dldo4: 700 <--> 3300 mV at 700 mV 
[    0.492000] axp22_eldo1: 700 <--> 3300 mV at 1800 mV 
[    0.504000] axp22_eldo2: 700 <--> 3300 mV at 3300 mV 
[    0.508000] axp22_eldo3: No configuration
[    0.512000] axp22_eldo3: 700 <--> 3300 mV at 700 mV 
[    0.516000] axp22_dc5ldo: No configuration
[    0.520000] axp22_dc5ldo: 700 <--> 1400 mV at 1200 mV 
[    0.528000] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV 
[    0.536000] axp22_dcdc2: 600 <--> 1540 mV at 1140 mV 
[    0.548000] axp22_dcdc3: 600 <--> 1860 mV at 1100 mV 
[    0.556000] axp22_dcdc4: 600 <--> 1540 mV at 1500 mV 
[    0.564000] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV 
[    0.568000] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV 
[    0.576000] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV 
[    0.584000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.588000] Bluetooth: Core ver 2.19
[    0.592000] NET: Registered protocol family 31
[    0.596000] Bluetooth: HCI device and connection manager initialized
[    0.600000] Bluetooth: HCI socket layer initialized
[    0.604000] Bluetooth: L2CAP socket layer initialized
[    0.608000] Bluetooth: SCO socket layer initialized
[    0.612000] cfg80211: Calling CRDA to update world regulatory domain
[    0.612000] Switching to clocksource source timer
[    0.632000] NET: Registered protocol family 2
[    0.636000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.644000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.656000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.664000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.668000] TCP: reno registered
[    0.672000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.680000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.684000] NET: Registered protocol family 1
[    0.692000] RPC: Registered named UNIX socket transport module.
[    0.696000] RPC: Registered udp transport module.
[    0.700000] RPC: Registered tcp transport module.
[    0.708000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.712000] Unpacking initramfs...
[    0.736000] Initramfs unpacking failed: junk in compressed archive
[    0.744000] Freeing initrd memory: 1024K
[    0.748000] Disply Reset Status : On
[    0.752000] Display LCD register operation 
[    0.760000] Display.0 fps=60 (16 ms), wait= 6 jiffies, Pixelclk=28571428hz
[    0.764000] LCD : [1]=LCD connect to [5]=SYNCGEN0
[    0.772000] bt_bcm: rfkill initialized
[    0.776000] audit: initializing netlink socket (disabled)
[    0.780000] type=2000 audit(0.780:1): initialized
[    0.784000] highmem bounce pool size: 64 pages
[    0.800000] NFS: Registering the id_resolver key type
[    0.804000] fuse init (API version 7.18)
[    0.808000] msgmni has been set to 1085
[    0.816000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.820000] io scheduler noop registered
[    0.824000] io scheduler deadline registered
[    0.832000] io scheduler cfq registered (default)
[    0.836000] display.0 connected to fb.0  ...
[    0.840000] nxp-fb.0: dma addr = 0x63600000, buf[0xe32d8ec0]
[    0.844000] nxp-fb.0: dma addr = 0x63777000, buf[0xe32d9040]
[    0.852000] nxp-fb.0: dma addr = 0x638ee000, buf[0xe32d9200]
[    0.928000] nxp-fb 0: out[0], 800 * 480 - 32 bpp (phys:63600000 virt:0xe3600000 max:4608000)
[    0.936000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.944000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.948000] uart-pl011 uart-pl011.2: no DMA platform data
[    0.952000] uart-pl011 uart-pl011.3: no DMA platform data
[    0.960000] uart-pl011 uart-pl011.4: no DMA platform data
[    0.964000] uart-pl011 uart-pl011.5: no DMA platform data
[    0.968000] Matirx PWM init
[    0.972000] iio-adc	initialized
[    0.980000] loop: module loaded
[    0.984000] tun: Universal TUN/TAP device driver, 1.6
[    0.988000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.996000]  -- nxpmac initialize --
[    1.000000] stmmac - user ID: 0x37, Synopsys ID: 0x37
[    1.004000]  Ring mode enabled
[    1.008000]  DMA HW capability register supported
[    1.012000]  Enhanced/Alternate descriptors
[    1.016000] 	Enabled extended descriptors
[    1.020000]  RX Checksum Offload Engine supported (type 2)
[    1.024000]  TX Checksum insertion supported
[    1.028000]  Wake-Up On Lan supported
[    1.032000]  Enable RX Mitigation via HW Watchdog Timer
[    1.076000] stmmac: probed
[    1.080000] eth0: PHY ID 001cc915 at 0 IRQ 215 (stmmac-0:00)
[    1.084000] eth0: PHY ID 001cc915 at 7 IRQ 215 (stmmac-0:07) active
[    1.092000] PPP generic driver version 2.4.2
[    1.096000] PPP BSD Compression module registered
[    1.100000] PPP Deflate Compression module registered
[    1.108000] PPP MPPE Compression module registered
[    1.112000] NET: Registered protocol family 24
[    1.116000] usbcore: registered new interface driver asix
[    1.124000] usbcore: registered new interface driver cdc_ether
[    1.128000] usbcore: registered new interface driver net1080
[    1.132000] usbcore: registered new interface driver cdc_subset
[    1.140000] usbcore: registered new interface driver zaurus
[    1.144000] usbcore: registered new interface driver cdc_ncm
[    1.152000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.160000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    1.164000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    1.172000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    1.188000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    1.192000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.200000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.204000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    1.212000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    1.220000] usb usb1: SerialNumber: nxp-ehci
[    1.224000] hub 1-0:1.0: USB hub found
[    1.228000] hub 1-0:1.0: 3 ports detected
[    1.232000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.436000] Core Release: 2.93a
[    1.440000] Setting default values for core params
[    1.444000] Finished setting default values for core params
[    1.652000] Using Buffer DMA mode
[    1.656000] Dedicated Tx FIFOs mode
[    1.660000] dwc_otg dwc_otg: DWC OTG Controller
[    1.664000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.672000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.676000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.684000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.688000] usb usb2: Product: DWC OTG Controller
[    1.696000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.700000] usb usb2: SerialNumber: dwc_otg
[    1.708000] hub 2-0:1.0: USB hub found
[    1.708000] hub 2-0:1.0: 1 port detected
[    1.716000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.720000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.728000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.736000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.800000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.804000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.812000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.820000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.824000] usb usb3: SerialNumber: nxp-ohci
[    1.828000] hub 3-0:1.0: USB hub found
[    1.832000] hub 3-0:1.0: 3 ports detected
[    1.840000] usbcore: registered new interface driver cdc_acm
[    1.844000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.852000] Initializing USB Mass Storage driver...
[    1.856000] usbcore: registered new interface driver usb-storage
[    1.864000] USB Mass Storage support registered.
[    1.868000] usbcore: registered new interface driver usbserial
[    1.872000] usbcore: registered new interface driver usbserial_generic
[    1.880000] USB Serial support registered for generic
[    1.884000] usbserial: USB Serial Driver core
[    1.892000] usbcore: registered new interface driver ch341
[    1.896000] USB Serial support registered for ch341-uart
[    1.900000] usbcore: registered new interface driver cp210x
[    1.908000] USB Serial support registered for cp210x
[    1.912000] usbcore: registered new interface driver ftdi_sio
[    1.920000] USB Serial support registered for FTDI USB Serial Device
[    1.924000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[    1.932000] usbcore: registered new interface driver option
[    1.936000] USB Serial support registered for GSM modem (1-port)
[    1.944000] usbcore: registered new interface driver pl2303
[    1.948000] USB Serial support registered for pl2303
[    1.952000] usbcore: registered new interface driver ti_usb_3410_5052
[    1.960000] USB Serial support registered for TI USB 3410 1 port adapter
[    1.968000] USB Serial support registered for TI USB 5052 2 port adapter
[    1.972000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[    1.980000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.988000] android_usb gadget: Number of LUNs=1
[    1.992000]  lun0: LUN: removable file: (no medium)
[    2.000000] android_usb gadget: android_usb ready
[    2.004000] mousedev: PS/2 mouse device common for all mice
[    2.008000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    2.016000] usbcore: registered new interface driver xpad
[    2.024000] input: ft5x0x_ts as /devices/virtual/input/input1
[    2.036000] ft5x0x_ts 2-0038: Firmware version 0x07
[    2.040000] ft5x0x_ts 2-0038: FocalTech ft5x0x TouchScreen initialized
[    2.048000] i2c-core: driver [IT7260-ts] using legacy suspend method
[    2.052000] i2c-core: driver [IT7260-ts] using legacy resume method
[    2.060000] <<-GTP-INFO->> GTP driver installing...
[    2.064000] himax_ts 2-0048: Unable to get DevId
[    2.068000] touchscreen-1wire	initialized
[    2.072000] backlight-1wire	initialized
[    2.080000] input: fa_ts_input as /devices/virtual/input/input2
[    2.084000] ts-if	initialized
[    2.088000] [RTC] day=2016.01.01 time=08:02:08
[    2.092000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    2.100000] i2c /dev entries driver
[    2.104000] ...................................ov5640_probe 2234
[    2.108000] ...................................ov5640_video_probe 2193
[    2.116000] ov5640 0-003c: reg_read: i2c read error, reg: 300a
[    2.124000] OV5640 read error!!!!!!!!!!!!!!!
[    2.128000] ov5640_initialize_ctrls.............1794...........
[    2.136000] nxp_hdmi_cec_probe success
[    2.140000] device-mapper: uevent: version 1.0.3
[    2.144000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    2.152000] Bluetooth: HCI UART driver ver 2.2
[    2.156000] Bluetooth: HCI H4 protocol initialized
[    2.164000] DVFS: ASV[0] IDS(10mA,  8) Ro(110,101)
[    2.172000] DVFS: regulator vdd_arm_1.3V
[    2.176000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    2.180000] cpuidle: using governor ladder
[    2.184000] cpuidle: using governor menu
[    2.188000] Synopsys Designware Multimedia Card Interface Driver
[    2.196000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    2.204000] mmc0: no vmmc regulator found
[    2.208000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    2.216000] dw_mmc dw_mmc.0: Version ID is 250a
[    2.220000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    2.228000] dw_mmc dw_mmc.1: Using PIO mode.
[    2.232000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.244000] mmc1: no vmmc regulator found
[    2.248000] dw_mmc dw_mmc.1: Version ID is 250a
[    2.252000] dw_mmc dw_mmc.1: DW MMC controller at irq 44, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    2.264000] usbcore: registered new interface driver usbhid
[    2.268000] usbhid: USB HID core driver
[    2.276000] ADC: CHs 8, 200000(1000000 ~ 130208) sample rate, polling mode, scale=166(bit 6)
[    2.280000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz, actual 25000000HZ div = 1)
[    2.280000] mmc0: new SDHC card at address 0001
[    2.280000] mmcblk0: mmc0:0001 SD16G 7.50 GiB 
[    2.284000]  mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[    2.304000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.316000] ashmem: initialized
[    2.320000] logger: created 256K log 'log_main'
[    2.324000] logger: created 256K log 'log_events'
[    2.328000] logger: created 256K log 'log_radio'
[    2.336000] logger: created 256K log 'log_system'
[    2.340000] snd pcm: register sound platform 'nxp-pcm'
[    2.344000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287980hz, RFS=256
[    2.476000] asoc: ES8316 HiFi <-> nxp-i2s.0 mapping ok
[    2.484000] spdif-tx: 48000(47348)Hz, MCLK=12121212hz HDMI out
[    2.492000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok
[    2.496000] GACT probability NOT on
[    2.500000] Mirror/redirect action on
[    2.504000] u32 classifier
[    2.508000]     Actions configured
[    2.512000] Netfilter messages via NETLINK v0.30.
[    2.516000] nf_conntrack version 0.5.0 (12943 buckets, 51772 max)
[    2.524000] ctnetlink v0.93: registering with nfnetlink.
[    2.528000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    2.536000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    2.540000] xt_time: kernel timezone is -0000
[    2.548000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.552000] arp_tables: (C) 2002 David S. Miller
[    2.556000] TCP: cubic registered
[    2.560000] Initializing XFRM netlink socket
[    2.564000] NET: Registered protocol family 10
[    2.568000] Mobile IPv6
[    2.572000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    2.576000] IPv6 over IPv4 tunneling driver
[    2.584000] NET: Registered protocol family 17
[    2.588000] NET: Registered protocol family 15
[    2.592000] Bluetooth: RFCOMM TTY layer initialized
[    2.596000] Bluetooth: RFCOMM socket layer initialized
[    2.600000] Bluetooth: RFCOMM ver 1.11
[    2.604000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    2.612000] Bluetooth: BNEP filters: protocol multicast
[    2.616000] Bluetooth: BNEP socket layer initialized
[    2.620000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.628000] Bluetooth: HIDP socket layer initialized
[    2.632000] NET: Registered protocol family 35
[    2.636000] Registering the dns_resolver key type
[    2.640000] Registering SWP/SWPB emulation handler
[    2.648000] axp22_dcdc5: incomplete constraints, leaving on
[    2.656000] axp22_dcdc4: incomplete constraints, leaving on
[    2.664000] axp22_dcdc3: incomplete constraints, leaving on
[    2.668000] axp22_dcdc2: incomplete constraints, leaving on
[    2.676000] axp22_dcdc1: incomplete constraints, leaving on
[    2.684000] axp22_dc5ldo: incomplete constraints, leaving on
[    2.688000] axp22_eldo2: incomplete constraints, leaving on
[    2.696000] axp22_eldo1: incomplete constraints, leaving on
[    2.704000] axp22_dldo1: incomplete constraints, leaving on
[    2.712000] axp22_aldo3: incomplete constraints, leaving on
[    2.720000] axp22_aldo2: incomplete constraints, leaving on
[    2.724000] axp22_aldo1: incomplete constraints, leaving on
[    2.732000] axp22_ldo1: incomplete constraints, leaving on
[    2.736000] otg_wakelock_init: No USB transceiver found
[    2.744000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-01 08:02:09 UTC (1451635329)
[    2.752000] TMU: register adc.2 to hwmon
[    2.756000] ALSA device list:
[    2.760000]   #0: I2S-ES8316
[    2.760000]   #1: SPDIF-Transciever
[    2.764000] Freeing init memory: 224K
[    2.768000] Write protecting the kernel text section c0008000 - c0854000
[    2.776000] rodata_test: attempting to write to read-only section:
[    2.784000] write to read-only section trapped, success
[    2.860000] type=1403 audit(1451635329.612:2): policy loaded auid=4294967295 ses=4294967295
[    2.868000] SELinux: Loaded policy from /sepolicy
[    2.876000] type=1404 audit(1451635329.628:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[    3.132000] HDMI HPD State 0x0
[    4.040000] init: /init.nanopi2.rc: 51: invalid command 'restorecon_recursive'
[    4.048000] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[    4.128000] init: /dev/hw_random not found
[    4.276000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    4.328000] EXT4-fs (mmcblk0p3): recovery complete
[    4.336000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[    4.376000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p3
[    4.528000] e2fsck: e2fsck 1.41.14 (22-Dec-2010)
[    4.532000] e2fsck: cache: clean, 12/27392 files, 3535/109568 blocks
[    4.564000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[    5.140000] EXT4-fs (mmcblk0p7): recovery complete
[    5.144000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[    5.200000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p7
[    5.236000] e2fsck: e2fsck 1.41.14 (22-Dec-2010)
[    5.240000] e2fsck: userdata: clean, 1082/158720 files, 54868/624468 blocks
[    5.268000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[    5.308000] setting PHY_BASEADDR_POWER_GATE, set 1
[    5.312000] setting PHY_BASEADDR_PMU_ISOLATE+4, set 0
[    5.320000] setting PHY_BASEADDR_PMU_ISOLATE+8, set 0
[    5.324000] setting PHY_BASEADDR_PMU_ISOLATE, set 1
[    5.332000] read PHY_BASEADDR_PMU_ISOLATE + 0xC
[    5.336000] Wait Power UP Ack(powerUpAck=0x00000000)
[    5.340000] setting ClockGen, set 1
[    5.344000] setting Reset VR addr(0xf0012008)
[    5.352000] setting PHY_BASEADDR_VR_PMU addr(0xf0072000)
[    5.356000] Vr: VR device driver loaded(ver1.2) for s5p4418
[    5.424000] init: /dev/hw_random not found
[    5.440000] healthd: No charger supplies found
[    5.444000] healthd: BatteryStatusPath not found
[    5.444000] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[    5.456000] healthd: BatteryHealthPath not found
[    5.464000] healthd: BatteryPresentPath not found
[    5.468000] healthd: BatteryCapacityPath not found
[    5.472000] healthd: BatteryVoltagePath not found
[    5.476000] healthd: BatteryTemperaturePath not found
[    5.480000] healthd: BatteryTechnologyPath not found
[    5.488000] binder: 106:106 transaction failed 29189, size 0-0
[    5.592000] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
[    5.600000] init: powerctl: cannot expand '${sys.powerctl}'
[    5.604000] init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
[    5.616000] init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
[    5.628000] android_usb: already disabled
[    5.636000] adb_open
[    5.636000] mtp_bind_config
[    5.640000] adb_bind_config
shell@nanopi2:/ $ [    6.536000] ov5640_link_setup
[    6.540000] camera_common_vin_setup_io
[    6.544000] ov5640 0-003c: reg_write: i2c write error, reg: 3103
[    6.552000] ov5640_init: failed to ov5640_write_array init regs
[    6.556000] ov5640_s_power.............1944...........
[    6.564000] nxp_hdmi_link_setup: connected to me!!!
[   16.176000] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[   22.324000] healthd: battery l=0 v=0 t=0.0 h=1 st=1 chg=
[   22.416000] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[   22.424000] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[   22.432000] lowmemorykiller: oom_adj 1 => oom_score_adj 58
[   22.436000] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[   22.440000] lowmemorykiller: oom_adj 3 => oom_score_adj 176
[   22.448000] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[   22.452000] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[   23.008000] eth0: device MAC address b2:7c:82:ef:46:aa
[   23.188000] acc_open
[   23.188000] acc_release
[   26.048000] init: sys_prop: permission denied uid:1003  name:service.bootanim.exit
